- Made in the USA
- Family-owned, 4 generations
-
"Good enough won't do - it must be right!" K.B. Danuser, Founder
|
|
|
|
|
|
IMPORTANT
SAFETY MESSAGE Safety is a primary concern in the design, manufacture, sale, and use of post hole diggers. As manufacturers of post hole diggers, we want to confirm to you, our customers, our concern for safety. We also want to remind you about the simple, basic, and common sense rules of safety when using a post hole digger. Failure to follow these rules can result in severe injury or death to operators or bystanders. It is essential that everyone involved in the assembly, operation, transport, maintenance, and storage of this equipment be aware, concerned, prudent, and properly trained in safety. The majority of accidents involve entanglement on the driveline or auger. This entanglement risk becomes greater when you replace our shear bolts with bolts longer than those specified by the manufacturer. This improper replacement occurs most often on machines that are loaned or rented to someone who has not read the owner's manual and is not familiar with a post hole digger. Our current production machines include, as standard equipment, guards or shields for auger adapters, drivelines, pinions, and safety signs. Older machines can be retrofitted to add these new guards or shields and, of course, safety signs. If you have an older machine which does not have standard safety equipment, please contact your dealer about bringing your machine up to the current level of safety. Below
are some of the most important safety rules to be understood and followed
by anyone who works with post hole diggers: |
|
||||||||||
|
||||||||||
|
||||||||||
|
||||||||||
|
||||||||||
|
Following these simple, basic safety rules, as well as others identified in the owner's manual and in product safety signs, will help minimize the possibility of accidents and increase your productivity in using this product. Be careful and make sure that everyone who operates the digger knows and understands that it is a very powerful piece of machinery, and if used improperly, serious injury or death may result. The final responsibility for safety rests with the operator of this machine. Update your older Danuser PTO Digger to current production safety standards and provide parts availability in the future.
F-Series
CURRENT
F-SERIES DIGGER
! DO
NOT OPERATE YOUR OLDER F-SERIES PTO DIGGER UNTIL YOU HAVE UPDATED TO
CURRENT PRODUCTION SAFETY STANDARDS. Current production Danuser F-Series PTO
Diggers include a # 7562 Pinion Assembly.
They have a black plastic Pinion Guard and black plastic guards
on the driveline, and the driveline will be connected to the input
pinion using a roll pin.
If
the serial number of your F-Series PTO Digger is 60,001 to 71,199 and
the unit has not been converted to the # 7562 Pinion Assembly, you
need to purchase a # 7578
Conversion Kit. The # 7578 Conversion Kit includes a pinion with
hardware, Pinion Guard, gaskets, grease seals, all driveline parts out
through the center cross at the U-Joint on the gearbox, and the # 7270
Auger Adapter Guard for 2-3/8" diameter center column augers.
This # 7578 kit is required on all diggers with serial numbers
ranging from 60,001 to 71,199. The
# 7580 Conversion Kit is the same as the # 7577 Conversion Kit, except
it comes with a # 9545 Auger Adapter Guard for 3-5/8" diameter
center column augers. The
# 7581 Conversion Kit is the same as the # 7578 Conversion Kit, except
it comes with a # 9545 Auger Adapter Guard for 3-5/8" diameter
center column augers.
To
install these conversion kits, you will need to disassemble the
gearbox. Instructions
sheets are provided in the kits.
Your dealer may offer installation for a fee.
After the conversion has been made and the gearbox is
assembled, you will need to add 3 lbs. of
Shell Alvania EP2 Grease (old name-Texaco MultiFax-EP2) or
equivalent. DO NOT ADD OIL TO THE F-SERIES GEARBOX. If you have any questions, concerns, or would like to place an order, contact Danuser Machine Company, Inc. at (573) 642-2246 or e-mail sales@danuser.com.
G20/40 Current
production Danuser G20/40 PTO Diggers include a # 6136 Auger Adapter
Guard. If the serial
number of your G20/40 is prior to 11,152, you need to purchase a #
6136 Auger Adapter Guard. This guard is required on all G20/40 PTO
Diggers. See photograph below.
DO NOT
OPERATE THE G20/40 PTO DIGGER UNTIL THE This
Guard Kit is sold direct at NET PRICE plus shipping:
If you have any questions, concerns, or would like to place an order, contact Danuser Machine Company, Inc. at (573) 642-2246 or e-mail sales@danuser.com.
|
||||||||||
Safety
